SCT x3 3200 tuner - Stage 2

Product Code: SCT-Custom-2

Usually Ships in 24 Hours

Qty:

Stage 2 tuning is for a turbo or supercharger configuration. Wideband airfuel loggers are needed to tune this setup. Hemifever Tuning supports 1996 through 2003 SCT supported vehicles. Verify your supported vehicle in the Technical Specs

* Verify pcm p/n before ordering

The SCT XCalibrator 3 can store up to 10 Custom Tune files, while storing the stock factory tune for easy restoration back to the stock configuration. Custom tuning is required if you have installed a turbo or supercharger. Stage 2 is also needed for open loop tuning. I'll work with you and email tunes to get your vehicle running its optimum in the current configuration. Once tuned, changes that you make which require additional tuning will be subject to additional tuning fees.

Idle, timing, and fuel curves can be changed to remove rich engine lights or fix idle problems. With a 2 bar map sensor and large injectors, we can dial in your forced induction configuration.

Response & Gas MileageFlashes PCM quickly & easily via OBDII diagnostic port!Retains Stock Program for easy restoration back to stock!Available for most 1996 - 2012 Dodge Gas Truck's and Hemi'sReads and clears engine codes

Ability to tune with a 2 bar map sensor and larger injectors

If you have purchased our Stage 2 tuning option and require additional changes once the original tune has been completed, there will be a $125 tuning fee

'04 - '06 HEMI Vehicles

'96 - '06 SRT10 Dodge Viper

'04 - '06 SRT10 Truck

'96+ V10 Magnum (non SRT10) Truck

3.9L Engine Supported Vehicles:

'96 - '03 RAM - 3.9L

'96 - '03 DAKOTA - 3.9L

4.7L Engine Supported Vehicles:

'99 - '04 GC - 4.7L

'00 - '06 DAKOTA - 4.7L

'00 - '03 DURANGO - 4.7L

'00 - '06 RAM - 4.7L *most all* through '06 4.7 except '06 Dakota manual trans

5.2L Engine Supported Vehicles:

'96 - 03 RAM 5.2L

'96 - '99 RAM VAN - 5.2L

'96 - 99 DAKOTA - 5.2L

'96 - '99 GC 5.2L

5.9L Engine Supported Vehicles:

'96 - '03 RAM - 5.9L

'98 - '03 DAKOTA - 5.9L

'98 - '03 DURANGO - 5.9L

'96 - '98 GC - 5.9L

Here is a walk-through for data logging on the device using the X3.

•Plug in the X3 to the vehicles OBD2 port.
•Scroll down to Data Logging, Press Select.
•Then Scroll down to Setup Monitor, Press Select.
•Config Analog Inputs? Select Yes or No, answering yes will allow you to connect a wideband or any other 0-5V component to the device analog input
•Pick Diesel or Gas, then press select.
•You are now ready to pick the pids.
oSelect them by highlighting them and then pressing select. You’ll notice that an Arrow will show next to the PID once selected.
oYou can select up to 20 Pids. NOTE: Default parameters are generated from a generic list of readable PCM parameters. It is possible that some pids shown will not be log able on your particular vehicle.
•Press Cancel to Exit from the list of Pids.
•This will bring you to a Save Data Configuration Menu.
oSelect – Save OK, Left – Back, Cancel – Exit
•Start Data Logging
oSelect – OK, Cancel – Exit
•A Message will display stating to make sure the vehicle is running, press Select to Start Recording.
•Once The Log has started, you can press LEFT/RIGHT arrows to view additional PIDS.
•Select will Stop Recording.
•Cancel will Exit the Log.

•You can Review this Log using a Computer with Livelink 4.24 or greater installed.
•Once 4.24 is installed and open…
•Then press: File/ Import Data log file from X3/livewire.
•A pop up box appears, Select Datalog0.dat from the list, then Press Ok.
•This will open and display the saved datalog.

SEARCH

SEARCH

SCT x3 3200 tuner - Stage 2

Description

Features

Technical Specs

Extended Information

Reviews

PRODUCTS

ABOUT US

MY ACCOUNT

HELPFUL INFO

Stay Tuned for Updates & Deals